technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 1 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen features B popular t-1 3/4 round package. B high efficiency. B available on tape and reel. B reliable and robust. B uv resistant epoxy B the product itself will remain within rohs compliant version . descriptions B the series is specially designed for applications requiring higher brightness. B the led lamps are available with different colors, intensities, epoxy colors, etc. applications B color graphic signs B message boards B variable message signs (vms) B commercial outdoor advertising device selection guide led part no. chip material emitted color lens color stopper 7383/y7c3-arua/ms algainp brilliant yellow water clear no 7383/y7c3-arua/p/ms algainp brilliant yellow water clear yes
technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 2 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen package dimensions notes: B all dimensions are in millimeters, tolerance is 0.25mm except being specified. B protruded resin under flange is 1.5mm max led.
technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 3 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen absolute maximum ratings (ta=25 ) parameter symbol rating units forward current i f 50 ma pulse forward current *1 i fp 160 ma operating temperature t opr -40 ~ +85 storage temperature t stg -40 ~ +100 electrostatic discharge esd 2k v soldering temperature *2 t sol 260 power dissipation p d 115 mw reverse voltage v r 5 v notes: soldering time Q 5 seconds. electro-optical characteristics (ta=25 ) parameter symbol condition min. typ. max. units forward voltage v f i f =20ma 1.8 2.0 2.6 v luminous intensity i v i f =20ma 4500 7150 11250 mcd viewing angle 2 1/2 i f =20ma -- 30 -- deg peak wavelength p i f =20ma -- 591 -- nm dominant wavelength d i f =20ma 586 589 594 nm spectrum radiation bandwidth ? i f =20ma -- 15 -- nm reverse current i r v r =5v -- -- 10 a
technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 4 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen rank combination (i f =20ma) rank r s t u luminous intensity 4500~5650 5650~7150 7150~9000 9000~11250 *measurement uncertainty of luminous intensity: 10% unit: :mcd rank 1 2 3 4 forward voltage 1.8~2.0 2.0~2.2 2.2~2.4 2.4~2.6 *measurement uncertainty of forward voltage: 0.1v unit:v rank 1 2 dominant wavelength 586~590 590~594 *measurement uncertainty of dominant wavelength 1.0nm unit:nm *the quantity ratio of the ranks is decided by everlight.
technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 5 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen 0 20406080100 0 10 20 30 40 50 60 forward current(ma) ambient temperature ta( o c) 1.01.52.02.53.03.5 0 10 20 30 40 50 forward current(ma) forward voltage(v) 0 1020304050 0.0 0.5 1.0 1.5 2.0 2.5 relative luminous intensity(a.u.) forward current(ma) 25 30 35 40 45 50 55 60 65 70 0.0 0.5 1.0 1.5 2.0 relative luminous intensity(a.u.) ambient temperature ta( o c) 0 10 20 30 40 50 60 70 80 90 o o o o o o o o o o 0 1.0 1.0 0.5 30 o 60 o 90 o 0.5 0 relative intensity(a.u.) radiation angle 450 500 550 600 650 700 0.0 0.2 0.4 0.6 0.8 1.0 relative intensity(a.u.) wavelength(nm) typical electro-optical characteristics curves relative intensity vs. wavelength forward current vs. forward voltage relative intensity vs. ambient temp. relative intensity vs. forward current forward current vs. ambient temp. radiation characteristics
technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 6 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen pb el ectrostatic electronagnetic magnetic or radioactive relds anti-static for 750 label packing specification anti-electrostatic bag inner carton label form specification cpn: customer?s production number p/n : production number qty: packing quantity cat: ranks of luminous intensity and forward voltage hue: rank of dominant wavelength outside carton ref: reference lot no: lot number made in taiwan: production place packing quantity 1. 500 pcs/1 bag, 5 bags/1 inner carton 2. 10 inner cartons/1 outside carton
technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 7 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen notes 1. lead forming ? during lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb. ? lead forming should be done before soldering. ? avoid stressing the led package during lead s forming. the stress to the base may damage the led?s characteristics or it may break the leds. ? cut the led leadframes at room temperature. cutting the leadframes at high temperatures may cause failure of the leds. ? when mounting the leds onto a pcb, the pcb holes must be aligned exactly with the lead position of the led. if the leds are m ounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the leds. 2. storage ? the leds should be stored at 30c or less a nd 70%rh or less after being shipped from everlight and the storage life limits are 3 mont hs. if the leds are stored for 3 months or more, they can be stored for a year in a s ealed container with a nitrogen atmosphere and moisture absorbent material. ? please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can occur. 3. soldering ? careful attention should be paid during sold ering. when soldering, leave more then 3mm from solder joint to epoxy bulb, and soldering beyond the base of the tie bar is recommended.
technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 8 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen prehead laminar wave fluxing ? recommended soldering conditions: hand soldering dip soldering temp. at tip of iron 300 max. (30w max.) preheat temp. 100 max. (60 sec max.) soldering time 3 sec max. bath temp. & time 260 max., 5 sec max distance 3mm min.(from solder joint to epoxy bulb) distance 3mm min. (from solder joint to epoxy bulb) ? recommended soldering profile ? avoiding applying any stress to the lead fr ame while the leds are at high temperature particularly when soldering. ? dip and hand soldering should not be done more than one time ? after soldering the leds, the epoxy bulb should be protected from mechanical shock or vibration until the leds return to room temperature. ? a rapid-rate process is not recommended for cooling the leds down from the peak temperature. ? although the recommended soldering conditions ar e specified in the above table, dip or handsoldering at the lowest possible temperature is desirable for the leds.
technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 9 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen ? wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder wave. 4. cleaning ? when necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than one minute. dry at room temperature before use. ? do not clean the leds by the ultrasonic. when it is absolutely necessary, the influence of ultrasonic cleaning on the leds depends on factors such as ultrasonic power and the assembled condition. ultrasonic cleaning shall be pre-qualified to ensure this will not cause damage to the led 5. heat management ? heat management of leds must be taken in to consideration during the design stage of led application. the current should be de -rated appropriately by referring to the de-rating curve found in each product specification. ? the temperature surrounding the led in the application should be controlled. please refer to the data sheet de-rating curve. 6. esd (electrostatic discharge) ? electrostatic discharge (esd) or surge current (eos) can damage leds. ? an esd wrist strap, esd shoe strap or an tistatic gloves must be worn whenever handling leds. ? all devices, equipment and machinery must be properly grounded. ? use ion blower to neutralize the static charge which might have built up on surface of the leds plastic lens as a result of friction between leds during storage and handing. 7. other ? above specification may be changed w ithout notice. everlight will reserve authority on material change for above specification.
technical data sheet 7383/y7c3-arub/x/ms everlight electronics co., ltd. http\\:www.ev erlight.com rev 2 page: 10 of 10 device number : dle-0001576 prepared date:06-25-2009 prepared :grace shen ? when using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. everlight assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. ? these specification sheets include material s protected under copyr ight of everlight corporation. please don?t reproduce or cause anyone to reproduce them without everlight?s consent. everlight electronics co., ltd. tel: 886-2-2267-2000, 2267-9936 office: no 25, lane 76, sec 3, chung yang rd, fax: 886-2267-6244, 2267-6189, 2267-6306 tucheng, taipei 236, taiw an, r.o.c http:\\www.everlight.com
|
